所属地区： --
所属机构： --
抱歉，该信息暂无中文翻译信息，为您显示项目原文信息。
Published date: 3 June 2024
Open opportunity - This means that the contract is currently active, and the buying department is looking for potential suppliers to fulfil the contract.
Lasers - 38636100
Industrial lasers - 38636110
Industrial machinery - 42000000
Yorkshire and the Humber
£0 to £250,000
4087/AMRC/CK/24
3 June 2024
3 July 2024
12pm
30 July 2024
31 October 2024
Supply contract
Open procedure (above threshold)
Any interested supplier may submit a tender in response to an opportunity notice.
This procedure can be used for procurements above the relevant contract value threshold.
Yes
Yes
As part of this requirement two applications are targeted: cutting trials with thin sheets of electrical steel for the production of electrical machine laminations and high rate cutting of CFRP panels. The remote laser cutting is being investigated as an alternative to traditional gantry-mounted fusion laser cutting. The benefits of this method of cutting are that the cut rate is increased and the thermal damage is reduced. Materials being investigated are high-silicon steel and cobalt iron. Sheet thicknesses could range from 0.35 mm down to 0.1 mm. A continuous-wave laser has been used in this investigation. But has been shown to produce an increased cut rate but creates more thermal damage to the material in the region of the cut. This is a result of firstly there being significant melting of the material, as well as vaporisation, and the fact that the molten material is not ejected from the component surface. A new short pulse laser is sought to overcome these issues. This new laser shall be capable of removing material in a way that produces reduced thermal damage compared to a traditional laser system. The new laser should be capable of cutting the steel sheets at a rate such that the resultant cut rate of the system is greater than that for a traditional gantry laser system. The second application addresses a requirement to put arrays of holes into aerospace-grade carbon fibre reinforced polymer composite panels typically associated with primary structure components, up to 3 mm thick. These holes are required to be produced at high rate (> 10 holes per second) without affecting any visible heat affected zone within the fibre or matrix surrounding the through-hole entry/exit/bore surfaces in the part being laser processed. Thermal damage is typically seen through either a charring/blackening or other discoloration on a surface and/or removal of additional material in the zone surrounding the intended hole's removal zone. These high-rate through holes are expected to be percussion drilled to maximise productivity and can be produced in parallel to manage thermal dissipation. The through holes required would range in size from 0.1 mm to 2 mm in diameter with a diameter tolerance of ±10%. The AMRC's existing optics can focus the spot across this range, however, alternative solutions to enable entry diameters, with minimal taper at high rate within this range are welcomed. The laser shall be capable of meeting this baseline. An ability to produce holes up to 25.4 mm in diameter using the trepanning method is also considered desirable.
Tender Process and Documentation:
This procurement is an open procedure.
The ITT can be downloaded by registering and expressing your interest on the University`s e-tendering system https://in-tendhost.co.uk/Sheffield
If you have any questions or comments in relation to this tender they must be submitted via the same e-tendering system, this can be accessed at https://in-tendhost.co.uk/Sheffield.
Additional text
Tender Process and Documentation:
This procurement is an open procedure.
The ITT can be downloaded by registering and expressing your interest on the University`s e-tendering system https://in-tendhost.co.uk/Sheffield
If you have any questions or comments in relation to this tender they must be submitted via the In-tend System, this can be accessed at https://in-tendhost.co.uk/Sheffield
Completed tenders must be returned through the same e-tendering system.
Closing date for receipt of tenders: 3rd of July 2024 at 12 noon (UK time) .
Follow the instructions given in the description or the more information section.
Rachel Hirst
THE UNIVERSITY OF SHEFFIELD,WESTERN BANK
SHEFFIELD
S102TN
England
01142157590
Is there anything wrong with this page?
本网站为您提供准确和及时的招投标信息，但招投标信息存在着变更的可能，请您务必在交易前向招标代理机构或招标人咨询投标详细要求，有关招标的具体要求及情况以招标代理机构或招标人的解释为准。
如果您对这篇招标信息有任何补充或修改建议，请告知我们。
猜你喜欢